Commit 291acaed authored by Rajan Palaniya's avatar Rajan Palaniya 💬
Browse files

sm8150-common: nfc: move to common tree

parent 685dbe8f
## This file is used by NFC NXP NCI HAL(external/libnfc-nci/halimpl/pn547)
## and NFC Service Java Native Interface Extensions (packages/apps/Nfc/nci/jni/extns/pn547)
###############################################################################
# Application options
# Logging Levels
# NXPLOG_DEFAULT_LOGLEVEL 0x01
# ANDROID_LOG_DEBUG 0x03
# ANDROID_LOG_WARN 0x02
# ANDROID_LOG_ERROR 0x01
# ANDROID_LOG_SILENT 0x00
NXPLOG_EXTNS_LOGLEVEL=0x02
NXPLOG_NCIHAL_LOGLEVEL=0x02
NXPLOG_NCIX_LOGLEVEL=0x03
NXPLOG_NCIR_LOGLEVEL=0x03
NXPLOG_FWDNLD_LOGLEVEL=0x02
NXPLOG_TML_LOGLEVEL=0x02
###############################################################################
# Nfc Device Node name
NXP_NFC_DEV_NODE="/dev/pn553"
###############################################################################
# Extension for Mifare reader enable
MIFARE_READER_ENABLE=0x01
###############################################################################
# Vzw Feature enable
VZW_FEATURE_ENABLE=0x01
###############################################################################
# File name for Firmware
NXP_FW_NAME="libpn553_fw.so"
###############################################################################
# System clock source selection configuration
#define CLK_SRC_XTAL 1
#define CLK_SRC_PLL 2
NXP_SYS_CLK_SRC_SEL=0x02
###############################################################################
# System clock frequency selection configuration
#define CLK_FREQ_13MHZ 1
#define CLK_FREQ_19_2MHZ 2
#define CLK_FREQ_24MHZ 3
#define CLK_FREQ_26MHZ 4
#define CLK_FREQ_32MHZ 5
#define CLK_FREQ_38_4MHZ 6
#define CLK_FREQ_52MHZ 7
NXP_SYS_CLK_FREQ_SEL=0x02
###############################################################################
# The timeout value to be used for clock request acknowledgment
# min value = 0x01 to max = 0x06
NXP_SYS_CLOCK_TO_CFG=0x06
###############################################################################
# NXP proprietary settings
NXP_ACT_PROP_EXTN={2F, 02, 00}
###############################################################################
# NFC forum profile settings
NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00}
###############################################################################
# NXP TVDD configurations settings
# Allow NFCC to configure External TVDD, two configurations (1 and 2) supported,
# out of them only one can be configured at a time.
NXP_EXT_TVDD_CFG=0x02
###############################################################################
#config1:SLALM, 3.3V for both RM and CM
NXP_EXT_TVDD_CFG_1={20, 02, 0F, 01, A0, 0E, 0B, 31, 01, 01, 31, 00, 00, 00, 01, 00, D0, 0C}
###############################################################################
#config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM,
#monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms
NXP_EXT_TVDD_CFG_2={20, 02, 0F, 01, A0, 0E, 0B, 11, 01, C2, B2, 00, B2, 1E, 1F, 00, D0, 0C}
###############################################################################
# Set configuration optimization decision setting
# Enable = 0x01
# Disable = 0x00
NXP_SET_CONFIG_ALWAYS=0x00
###############################################################################
# Core configuration rf field filter settings to enable set to 01 to disable set
# to 00 last bit
NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 00 }
###############################################################################
# To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set
# to 0x00
NXP_I2C_FRAGMENTATION_ENABLED=0x00
###############################################################################
# Mifare Classic Key settings
#NXP_CORE_MFCKEY_SETTING={20, 02, 25,04, A0, 51, 06, A0, A1, A2, A3, A4, A5,
# A0, 52, 06, D3, F7, D3, F7, D3, F7,
# A0, 53, 06, FF, FF, FF, FF, FF, FF,
# A0, 54, 06, 00, 00, 00, 00, 00, 00}
###############################################################################
#Enable SWP full power mode when phone is power off
NXP_SWP_FULL_PWR_ON=0x00
###############################################################################
#### Select the CHIP ####
#PN547C2 0x01
#PN65T 0x02
#PN548AD 0x03
#PN66T 0x04
#PN551 0x05
#PN67T 0x06
#PN553 0x07
#PN80T 0x08
NXP_NFC_CHIP=0x08
###############################################################################
# CE when Screen state is locked
# This setting is for DEFAULT_AID_ROUTE,
# DEFAULT_DESFIRE_ROUTE and DEFAULT_MIFARE_CLT_ROUTE
# Disable 0x00
# Enable 0x01
NXP_CE_ROUTE_STRICT_DISABLE=0x01
###############################################################################
#Timeout in secs to get NFCEE Discover notification
NXP_DEFAULT_NFCEE_DISC_TIMEOUT=20
###############################################################################
NXP_DEFAULT_NFCEE_TIMEOUT=20
###############################################################################
#Timeout in secs
NXP_SWP_RD_START_TIMEOUT=0x0A
###############################################################################
#Timeout in secs
NXP_SWP_RD_TAG_OP_TIMEOUT=0x01
###############################################################################
#Set the default AID route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x01
# UICC 0x02
DEFAULT_AID_ROUTE=0x02
###############################################################################
# Configure the default NfcA/IsoDep techology and protocol route. Can be
# either a secure element (e.g. 0xF4) or the host (0x00)
# host 0x00
# eSE 0x01
# UICC 0x02
DEFAULT_ISODEP_ROUTE=0x02
###############################################################################
# Configure the single default SE to use. The default is to use the first
# SE that is detected by the stack. This value might be used when the phone
# supports multiple SE (e.g. 0xC0 and 0x80) but you want to force it to use
# one of them (e.g. 0xC0).
# host 0x00
# eSE 0x01
# UICC 0x02
DEFAULT_OFFHOST_ROUTE=0x02
###############################################################################
# Configure the single default SE to use. The default is to use the first
# SE that is detected by the stack. This value might be used when the phone
# supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use
# one of them (e.g. 0xF4).
# host 0x00
# eSE 0x01
# UICC 0x02
DEFAULT_TECH_ABF_ROUTE=0x02
###############################################################################
#Set the default Felica T3T System Code OffHost route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x01
DEFAULT_SYS_CODE_ROUTE=0x00
###############################################################################
#Set the default AID Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Screen On lock
# bit pos 4 = Screen off unlock
# bit pos 5 = Screen Off lock
DEFAULT_AID_PWR_STATE=0x3B
###############################################################################
#Set the Mifare Desfire Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked
# bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked
# bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked
DEFAULT_ISODEP_PWR_STATE=0x3B
###############################################################################
#Set the Mifare CLT Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked
# bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked
# bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked
DEFAULT_OFFHOST_PWR_STATE=0x3B
###############################################################################
#Set Tech A,B,F Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked
# bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked
# bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked
DEFAULT_TECH_ABF_PWR_STATE=0x3B
###############################################################################
#Set the SYS_CODE Power state :
#This settings will be used when application does not set this parameter
# bit pos 0 = Switch On
# bit pos 1 = Switch Off
# bit pos 2 = Battery Off
# bit pos 3 = Switched On Sub-State 1 : Screen is off and device is unlocked
# bit pos 4 = Switched On Sub-State 2 : Screen is on and device is locked
# bit pos 5 = Switched On Sub-State 3 : Screen is off and device is locked
DEFAULT_SYS_CODE_PWR_STATE=0x00
###############################################################################
# Configure the NFC Extras to open and use a static pipe. If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
# for each UICC (where F3="UICC0" and F4="UICC1")
OFF_HOST_ESE_PIPE_ID=0x19
OFF_HOST_SIM_PIPE_ID=0x0A
###############################################################################
# Bail out mode
# If set to 1, NFCC is using bail out mode for either Type A or Type B poll.
NFA_POLL_BAIL_OUT_MODE=0x01
###############################################################################
# AID Matching platform options
# AID_MATCHING_L 0x01
# AID_MATCHING_K 0x02
AID_MATCHING_PLATFORM=0x01
###############################################################################
#CHINA_TIANJIN_RF_SETTING
#Enable 0x01
#Disable 0x00
NXP_CHINA_TIANJIN_RF_ENABLED=0x01
###############################################################################
#SWP_SWITCH_TIMEOUT_SETTING
# Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60].
# Timeout in milliseconds, for example
# No Timeout 0x00
# 10 millisecond timeout 0x0A
NXP_SWP_SWITCH_TIMEOUT=0x0A
###############################################################################
#Timeout value in milliseconds for NFCC standby mode.The range is between 5000
#msec to 20000 msec and zero is to disable.
NXP_NFCC_STANDBY_TIMEOUT=20000
###############################################################################
#Dynamic RSSI feature enable
# Disable 0x00
# Enable 0x01
NXP_AGC_DEBUG_ENABLE=0x00
###############################################################################
#Config to allow adding aids
#NFC on/off is required after this config
#1 = enabling adding aid to NFCC routing table.
#0 = disabling adding aid to NFCC routing table.
NXP_ENABLE_ADD_AID=0x01
###############################################################################
# Enable/Disable checking default proto SE Id
# Disable 0x00
# Enable 0x01
NXP_CHECK_DEFAULT_PROTO_SE_ID=0x01
###############################################################################
#NXP_CN_TRANSIT_CMA_BYPASSMODE_ENABLE
#Enable this config it prevents EMVCo PICC compliancy and Mifare backward compatibility works
#Disable this config EMVCo PICC compliancy works and Mifare backward compatibility will not work
#Default config is Disable
#Enable 0x01
#Disable 0x00
NXP_CN_TRANSIT_CMA_BYPASSMODE_ENABLE=0x00
###############################################################################
#NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE
#Enable/Disable block number checks for china transit use case
#Enable 0x01
#Disable 0x00
NXP_CN_TRANSIT_BLK_NUM_CHECK_ENABLE=0x01
###############################################################################
#Enable NXP NCI runtime parser library
#Enable 0x01
#Disable 0x00
NXP_NCI_PARSER_LIBRARY=0x00
###############################################################################
#This config will enable different level of Rf transaction debugs based on the
#following values provided. Decoded information will be printed in adb logcat
#Debug Mode Levels
#Disable Debug 0x00
#L1 Debug 0x01
#L2 Debug 0x02
#L1 & L2 Debug 0x03
#L1 & L2 & RSSI 0x04
#L1 & L2 & Felica 0x05
#NXP_CORE_PROP_SYSTEM_DEBUG=0x00
###############################################################################
# Enable/Disable Block Route feature.
# Block Route will restrict routing to first matched rule
# Block Route enable 0x01
# Block Route disable 0x00
AID_BLOCK_ROUTE=0x00
##############################################################################
# Timeout value in milliseconds to send response for Felica command received
NXP_HCEF_CMD_RSP_TIMEOUT_VALUE=5000
###############################################################################
# HAL library path for selftest
NXP_HAL_PATH="/vendor/lib64/hw/nfc_nci.pn54x.so"
###############################################################################
# Enable or Disable RF_STATUS_UPDATE to EseHal module
# Disable 0x00
# Enable 0x01
RF_STATUS_UPDATE_ENABLE=0x00
###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
# byte[0] NCI_PROTOCOL_18092_ACTIVE
# byte[1] NCI_PROTOCOL_B_PRIME
# byte[2] NCI_PROTOCOL_DUAL
# byte[3] NCI_PROTOCOL_15693
# byte[4] NCI_PROTOCOL_KOVIO
# byte[5] NCI_PROTOCOL_MIFARE
# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, 70, FF, FF}
###############################################################################
#White list of Hosts
#This values will be the Hosts(NFCEEs) in the HCI Network.
DEVICE_HOST_WHITE_LIST={80:81}
###############################################################################
#OffHost UICC route location for MultiSE
#UICC1 = 02
#UICC2 = 03
OFFHOST_ROUTE_UICC={02}
###############################################################################
# Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1.
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check
PRESENCE_CHECK_ALGORITHM=2
###############################################################################
# Extended APDU length for ISO_DEP
ISO_DEP_MAX_TRANSCEIVE=0xFEFF
###############################################################################
\ No newline at end of file
......@@ -219,7 +219,6 @@ PRODUCT_COPY_FILES += \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/init/vendor.sensors.qti.rc:$(TARGET_COPY_OUT_VENDOR)/etc/init/vendor.sensors.qti.rc \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/init/vendor.sensors.sscrpcd.rc:$(TARGET_COPY_OUT_VENDOR)/etc/init/vendor.sensors.sscrpcd.rc \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/init/vppservice.rc:$(TARGET_COPY_OUT_VENDOR)/etc/init/vppservice.rc \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/libnfc-nxp.conf:$(TARGET_COPY_OUT_VENDOR)/etc/libnfc-nxp.conf \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/libnfc-nxp_RF.conf:$(TARGET_COPY_OUT_VENDOR)/etc/libnfc-nxp_RF.conf \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/msm_irqbalance.conf:$(TARGET_COPY_OUT_VENDOR)/etc/msm_irqbalance.conf \
vendor/oneplus/sm8150-common/proprietary/vendor/etc/perf/commonresourceconfigs.xml:$(TARGET_COPY_OUT_VENDOR)/etc/perf/commonresourceconfigs.xml \
......
Supports Markdown
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment